Stone Backsplash: Slate, Travertine and Stacked Stone, Compared

A metal ceiling was sold to a small-town shopkeeper in the 1890s as a fireproof stand-in for ornamental plaster, and it is sold to an office fit-out today as a way to hide the sprinkler pipes. Both come up for the same two words, and almost nothing about one applies to the other. This guide maps the category: the four families a metal ceiling can belong to, the metals underneath each, the five ways they are held overhead, and where an 8-inch peel-and-stick aluminum tile fits in. What a metal ceiling is, and the four families the phrase covers Every metal ceiling is a sheet of metal fixed below a structure. The sheet, the structure and the reason change from one family to the next. Pressed and stamped tiles or panels. The decorative "tin ceiling": a repeating relief pattern pressed into thin sheet, sold as square plates, longer panels and matching cornice. This is the family a homeowner is almost always picturing, and the one WallWear's metal tile belongs to. Corrugated and profiled sheet. Roofing panel turned to face the room. The National Park Service records that the first commercial decorative metal ceilings in the United States, in the early 1870s, were corrugated iron borrowed from the roofing trade. Our guide to a corrugated metal ceiling covers what that profile does indoors. Flat architectural systems. Linear strips, planks, perimeter trims, floating clouds and perforated panels, nearly all suspended from a grid and specified for offices, retail, healthcare and schools. If a quote mentions a suspension grid, perforation percentages or acoustic backing, you are looking at an architectural metal ceiling, and there is no cut-down version for a kitchen. Exposed metal deck. The structural decking of a loft left visible: a ceiling made of metal rather than a metal ceiling product. If the listing talks instead about a pattern, a finish, a relief depth and a tile or panel size, you are in the decorative family. Decorative ceiling tiles explains why grid products and surface products are sized differently on purpose, and pressed, stamped, embossed decodes the vocabulary on the listing. The metals: steel, tin plate, galvanized steel, aluminum and copper The word "tin" has done more to muddle this subject than any other. The Park Service brief on historic decorative metal ceilings is blunt about it: the sheet steel commonly used "was neither tin-plated nor galvanized," and the makers of the day never used the word. The historic product was plain sheet steel, factory primed and meant to be painted, and the paint was its rust protection. Painted steel is that historic recipe. Strong, inexpensive, and dependent on an unbroken paint film to stay rust-free. Tin-plated steel is what most reproduction pressed-metal panels are stamped from today, because the thin tin layer makes the sheet less prone to rust than bare steel. The brief still calls back-priming it good practice. Galvanized steel carries a zinc coating: hot-dip galvanizing immerses the sheet in molten zinc, which bonds to the iron in alloy layers topped by pure zinc. It is the usual finish on corrugated panel and the source of the mottled, silvery look people want from a barn ceiling. Aluminum does not rust and weighs a fraction of steel, which is why it dominates the commercial systems and why WallWear uses it for an adhesive tile. The Park Service notes that aluminum suits patterns of low to moderate relief, which is exactly how a thin embossed tile is used; our piece on aluminum ceiling tiles goes deeper. Copper and zinc were special-order metals historically, used mostly in elaborate public, commercial or residential rooms, and they remain the premium end. Copper ceiling tiles separates solid copper from a copper finish. One more material shares the shelf without being a metal. PVC panels stamped to imitate pressed metal cost less than tin plate or aluminum, and the Park Service observes they come only in low relief. Faux tin ceiling tiles shows how to tell the two apart. How a metal ceiling is held up: five methods The material decides how a ceiling ages. The fixing decides whether you can install it yourself and what happens the day you want it gone. 1. Nail-up on furring Wood furring strips are nailed across the joists in a grid that matches the panel seams, then each 24-inch plate is nailed through pre-punched holes, edges overlapping so one nail passes through two sheets. Modern instructions often substitute a sheet of plywood as a simpler nailing base. Permanent, authentic for a steel reproduction, and carpentry before it is decoration. 2. Lay-in grid Lightweight panels, usually PVC or aluminum, rest in a suspended T-bar grid. Most commercial ceilings and most "faux tin" drop ceilings work this way. The grid is the ceiling; the panel is the finish. 3. Glue-up Panels bonded to a flat substrate with construction adhesive from a tube. No grid and no furring, but a wet adhesive, a cure time and a ceiling that is yours for good. 4. Peel-and-stick An embossed metal tile with the adhesive already on its back, pressed onto a clean, smooth, dry and sound surface. No furring and no plywood, because there is nothing to nail. The surface rule is strict: heavy texture rules a ceiling out, and the grease film above a range will defeat an adhesive that holds anywhere else. Our ceiling install guide covers judging the plane before the first tile goes up. 5. Clip-in and suspended systems Linear strips and planks clip to carriers or hang from a suspension, and floating clouds hang from cables: the architectural systems again, sold as a kit and installed by trade. For the three methods a homeowner actually chooses between, see the drop-in, nail-up and peel-and-stick comparison. Reading an interior metal ceiling: field, filler, molding and cornice A historic pressed-metal ceiling was a kit of four parts, and knowing them makes any interior metal ceiling easier to plan. The field is the repeating pattern that covers most of the plane, stamped on plates most commonly 24 inches square or 24 by 48. A molding frames the field. A filler runs between that frame and the wall, supplied in several widths so an out-of-square room could be absorbed without cutting into the pattern. A cornice turns the corner onto the wall. The relief of the field typically stood between three-eighths and three-quarters of an inch proud of the sheet. The logic transfers to a small modern tile. An 8-inch module lets the field run from the center outward, so the compromise lands in a narrow perimeter band, the filler's old job. What that band gets is the question tin molding, trim and ceiling medallions takes on, and tin ceiling panels vs. 8x8 tiles explains why seam count, not pattern, is what the eye reads from the floor. What a metal ceiling does to light, sound, moisture and fire Light. A metal plane reflects more than paint, and relief casts shadow, so a pressed ceiling reads differently at noon, under cabinet lights and under a single pendant. A pre-finished tile with contrast built into the relief gets that highlight without a painter. Sound. Hard metal reflects sound; it does not absorb it. Commercial systems earn their acoustic ratings from perforation, sometimes up to 65 percent open area, with absorbent material behind the holes. A solid decorative tile over drywall is acoustically close to the drywall it covers. Moisture. Steel needs its coating; the brief is explicit that paint on historic steel ceilings "served as a protective coating to deter oxidation and rust." Aluminum sidesteps the problem. WallWear's tile is water-resistant aluminum, which is why bathroom walls and ceilings are among its listed uses, and it is not a product for standing water or a shower enclosure. Fire. "Durable, handsome and fireproof" was the original pitch, and the metal itself is noncombustible. The brief records that a historic pressed-steel ceiling nailed to furring on wood joists carries a 30-minute rating, and one installed over intact plaster may reach an hour. Those figures describe historic assemblies evaluated under the building code; a decorative adhesive tile is a finish, not a fire-rated assembly, and we make no rating claim for it. Where a peel-and-stick aluminum tile sits in this map WallWear's metal tile is the decorative family reduced to its simplest form: an 8-by-8-inch tile of real, water-resistant aluminum with the pattern embossed into the metal, ten to a pack, and the brand puts a pack's coverage at roughly 4.44 square feet. It goes up by the peel-and-stick method above and trims with a box cutter or scissors, which is the whole tool list; there is no grout to mix and no professional to book. Ceilings, kitchen backsplashes and bathroom walls are its listed uses, on smooth surfaces only. The finishes cover most of the metals above without the metallurgy. Rustic Farmhouse sets gold scrollwork against a deep green ground, close to the two-color schemes period catalogs favored. Patina Copper carries the aged, green-flecked look of weathered copper. Silver Fleur is a polished-silver fleur-de-lis, and Teal and Silver Leaves puts silver relief on a saturated teal. Overhead work is harder than a backsplash because gravity pulls on the bond the entire time, so read the main install guide for peel and stick metal tile alongside the ceiling guide, and kitchen ceiling tiles in metal for the one room where the ceiling has to agree with the cabinets. On taking it down later: an adhesive tile comes away with far less effort than anything nailed or mortared, but how cleanly depends on the paint and surface beneath it, so test a corner tile first and follow the current product guidance. Frequently Asked Questions Is a tin ceiling the same thing as a metal ceiling? A tin ceiling is one family of metal ceiling: the pressed, patterned decorative kind. The name is a historical misnomer, since the original sheets were plain steel rather than tin plate. "Metal ceiling" is the wider term and also covers corrugated sheet and the flat, suspended systems used in commercial buildings, which have nothing to do with the decorative product. Do metal ceilings rust? Steel ones can. Historic pressed-steel ceilings relied on paint to keep rust away, and modern tin-plated reproductions still benefit from priming. Galvanized sheet is protected by its zinc coating until that coating is scratched through. Aluminum does not rust, which is why it is used for lightweight commercial panels and for WallWear's water-resistant tile. Are metal ceilings noisy? A solid metal surface reflects sound rather than absorbing it, so it will not quiet a room, though over drywall it changes very little. Commercial metal ceilings earn their acoustic performance from perforated panels backed with absorbent material, which is a different product. Choose a metal ceiling for its look and its light, not for sound control. Can you install a metal ceiling yourself? It depends on the fixing method. Nail-up steel panels mean furring or plywood, blocking for the cornice and a lot of overhead nailing, and suspended architectural systems are trade installations. Peel-and-stick aluminum tiles need only a smooth, clean, dry ceiling, a box cutter or scissors for trimming, and a second pair of hands, which keeps them within reach of a careful DIYer. Are metal ceilings expensive? The range is wide because the word covers everything from a plastic lay-in panel to a solid copper cornice stamped on a drop hammer. Material, sheet thickness, relief depth and what the price includes move the number most. Pricing every option per square foot, grid and fasteners included, is the only fair comparison, and our breakdown of what tin ceiling tiles cost shows the math.

A slab of slate and a panel of stacked stone can come from the same kind of rock and still ask completely different things of the person who wipes them down. That is the part a showroom sample never tells you. A stone backsplash is a good choice when you know which stone you are buying, how its surface behaves next to a cooktop, and what it will take to change your mind in ten years. What counts as a stone backsplash "Stone" covers several materials that look related on a mood board and behave very differently on a wall. Slate. A metamorphic rock formed from shale or mudstone. It is often sold with a cleft face, meaning the surface was split along the stone's natural layers instead of being ground flat. That gives it a rippled, matte character. Softer, lower grades can flake in thin layers, especially where they stay damp. Travertine. A calcite stone deposited by mineral springs. The small holes in it come from gas trapped as it formed, and it is sold either filled (the holes packed with a cement or resin filler) or unfilled. Limestone. Also calcite-based, usually soft in color and finish, and quieter in pattern than travertine. Granite and quartzite tile. Harder, denser stones, usually polished or honed flat. They behave the most like a countertop on the wall. Stacked stone. Thin strips of natural stone bonded to a backing in panels, laid so the strips create a ledged, three-dimensional face with no grout joints. It is not the same thing as manufactured stone veneer, which is cast from cement, aggregate and pigment to imitate rock. Marble belongs on this list too, but it has its own set of trade-offs, and our marble backsplash guide covers etching, sealing and slab installation in detail. Is a stacked stone backsplash hard to clean? Usually, yes, and the reason is geometry, not the stone itself. Every ledge on a stacked stone panel is a small horizontal shelf. Behind a range, grease and fine spatter land on those shelves and settle into the gaps between strips, where a cloth cannot follow. Renovation writers raise it often, and it is why stacked stone tends to be easier to live with on a wall that never sees a frying pan. Flat stone is a different experience. A honed slate, granite or limestone tile wipes down much like any tiled wall, with the grout lines as the weak point. Unfilled travertine sits in between: the open holes collect grime, which is a good argument for the filled version. For any of them, the Natural Stone Institute's care guidance is short and worth following: Clean with a pH-neutral stone cleaner, a stone soap, or a little gentle dish soap diluted in warm water. Skip vinegar, lemon and other acidic cleaners, and avoid abrasive powders. Go easy on ammonia-based products; frequent use can dull some stones. On stacked stone, a soft brush reaches into the ledges where a sponge snags. Acid matters more for some stones than others. Calcite stones (limestone, travertine and marble) can etch when citrus, tomato or vinegar sits on them, leaving a dull spot. Slate is generally more acid-resistant, though not immune, so a lemon-juice test on a spare piece tells you where your own tile stands. Sealing a stone backsplash: how to tell when it is due Most natural stone absorbs liquid to some degree, and sealing is common practice on a backsplash because it slows that absorption. A sealer makes stone more stain resistant. It does not make it stain proof, and it does not stop acid etching on calcite stones. How often to reseal depends on the stone and on the sealer, and published advice ranges from yearly to every few years. For stacked stone in a kitchen, the Natural Stone Institute suggests a penetrating sealer once a year. For everything else, test instead of following a calendar: Pour a small puddle of water, about three inches across, on a few spots that see the most splash. Wait around 15 to 30 minutes. If the water still beads on top, the seal is holding. If it has soaked in and left a darker patch, it is time to reseal with a product made for that stone. What installing a stone backsplash involves Stone tile goes up the way other heavy tile does: a mortar bed, careful layout, cuts on a wet saw, then grout and sealer. Stacked stone skips the grout but adds weight, and that changes what can sit behind it. Manufacturers do not agree on the wall. At least one large stone supplier says stacked stone should not go directly on drywall, and recommends replacing it with cement backer board or screwing cement board over it before setting panels in a high-performance thinset, with every panel back-buttered. Other ledger stone makers allow gypsum board indoors within limits. Read the instructions for the exact product you buy before you decide the existing wall will do. The practical upshot: a stone backsplash is usually a project with demolition and drying time built in, and its outlets often need box extenders because the finished face can sit well proud of the drywall. Is a stone backsplash outdated? The material is not; a particular version of it has had its moment. Editors writing about dated kitchens point mostly at the heavily textured, earth-toned "Tuscan" stone backsplash that was everywhere in the 2000s, and at busy stone mosaics, while full slabs and calm, large-format stone continue to show up in current design coverage. Treat that as taste, not a verdict. What keeps stone from looking tied to a decade is restraint. One stone, one finish and a simple layout read as architectural. A rough stacked stone wall with contrasting grout, a mosaic border and a speckled granite counter reads as a period piece, whatever year it went in. Updating a stone backsplash you already have Painting it You can paint stone, and plenty of homeowners have. The steps reported in practice are consistent: degrease thoroughly, scuff glossy areas, apply a bonding or masonry primer made for stone, then paint with a durable finish. What is missing is solid technical guidance from paint makers, and paint on stone is hard to undo, so treat it as a long-term decision. Our article on painting a tile backsplash covers the method and where it tends to fail. Covering it Peel-and-stick products, including WallWear's metal tile, need a smooth surface. Our product pages say plainly that the tiles are not suitable for textured walls, so stacked stone, cleft slate and tumbled travertine cannot be covered directly. The usual route is removal, and taking out any bonded backsplash often damages the wall surface behind it, which then needs patching or new board before anything else goes up. A flat, honed stone tile with level grout is a different case, closer to covering ceramic. How to judge whether that surface is ready is covered in metal tile over an existing tile backsplash. Metal and stone, and a lower-upkeep kind of relief A lot of what people love about stone is dimension: light catching a raised surface and a wall that looks crafted instead of printed. Embossed metal tile gives you relief from a different source. It is real aluminum, water-resistant, and the product pages describe it as made "for durability and easy cleaning." There is no grout and no porous face to seal, so the stone-care routine above simply does not apply. Metal also sits well beside stone that stays in the room. Patina Copper, a copper tone with a weathered finish, warms up a slate or warm-toned stone counter. Silver Fleur keeps a gray granite crisp, Pastel Painted Gold adds a soft, painterly warmth to pale limestone, while Teal and Silver Leaves brings a jolt of color to an all-neutral stone room. A pack is ten tiles at 8 by 8 inches, roughly 4.44 square feet of wall by the product page's own approximation. The brand's instructions are to peel, stick and trim to fit using a box cutter or scissors, and nothing beyond those two everyday cutters: no grout, no special tooling and no installer. Leave a gap of 10 inches or more between the tiles and the stovetop, which is the clearance WallWear recommends. For layout, pressing and the final trims, start with the step-by-step metal tile installation guide. Frequently Asked Questions Is natural stone good for a kitchen backsplash? It can be, as long as you match the stone to the spot. Dense, flat stones such as honed granite or slate are the easiest to live with behind a sink or range. Calcite stones like limestone and travertine can etch from acidic splashes, and stacked stone traps grease in its ledges. Seal according to the water test and clean with a pH-neutral product. How do you clean a stacked stone backsplash? Dust it first, then use a soft brush and a pH-neutral stone cleaner (or a few drops of gentle dish soap in a bucket of warm water), working into the ledges where grease settles. Rinse with a damp cloth and let it dry. Avoid vinegar, citrus cleaners and abrasive powders. A penetrating sealer, reapplied when water stops beading, makes the next cleaning noticeably easier. Can you install stacked stone over drywall? It depends on the product. At least one major stone supplier says no and recommends cement backer board, either replacing the drywall or screwing board over it. Some other ledger stone makers allow gypsum board indoors within height and weight limits. Follow the instructions for the exact panel you buy, since mortar and substrate requirements vary between manufacturers. Can peel and stick tile go over a stone backsplash? Only if the stone is flat and smooth. Peel-and-stick tile needs an even surface to bond, and WallWear's metal tiles are not suitable for textured walls, so stacked stone, cleft slate and tumbled stone have to come off first, with the wall repaired afterward. A honed, level stone tile with flush grout can be assessed like ceramic. Does slate need to be sealed? Sealing slate on a backsplash is common, because even a fairly dense stone absorbs some oil and pigment, and sealing makes stains easier to wipe away. Slate is generally more acid-resistant than limestone or travertine, but not immune. Use the water test to decide when to reseal, and pick a sealer labeled for slate or natural stone.

Countertops go in first, and the backsplash follows them. That is the short answer to whether the countertop or backsplash comes first, and it holds for nearly every kitchen. The longer answer covers why the counter sets the schedule, where the order bends, and how many days each kind of backsplash takes once its turn arrives. Countertop or backsplash first? Why the counter sets the line A backsplash has to start somewhere, and in a kitchen that somewhere is the top of the counter. The finished counter height is not fixed until the slab or laminate is actually sitting on the cabinets. Installers shim cabinets to level them, and those fractions of an inch decide where the work surface lands. Tile first and you are guessing at your bottom edge. The order also protects the work itself. Stone and quartz tops are templated by a fabricator once the cabinets are set, then cut, delivered and maneuvered into place. A finished wall of tile is the first thing a heavy slab bumps on the way in. Remodel planners put it plainly: no countertop order until the cabinets are in, so the measurements are real. So the standard sequence runs like this: Wall repairs, rough electrical and plumbing, then primer and paint. Flooring and cabinets, leveled and fixed. Countertops templated, fabricated and installed, along with the sink. Backsplash, from the counter up. Faucet, outlet and switch trim, range and other appliances. When the order bends: slab splashes, laminate and counter swaps A full-height slab backsplash When the backsplash is cut from the same stone as the counter, the fabricator handles both, and the backsplash still is not first. Some fabricators measure a full-height slab splash after the counters are installed, sometimes on the same visit, because they need the real top edge of the counter to cut against. Laminate with a built-in splash Post-formed laminate counters often arrive with a short backsplash curved up from the same sheet at the factory. Counter and splash are one piece, so they go in together; any decorative backsplash above still comes after. New counters, existing tile When you replace countertops and hope to keep the tile, the bottom row is often hard to save. Tile set tight to the old counter can chip or pull drywall with it when the old top is pried out, and remodeling guides recommend cutting the caulk line first to reduce that risk. Thickness changes the picture too. A typical laminate top is around 1 1/2 inches thick, while stone usually comes in 2 cm or 3 cm slabs, so the new surface may sit lower or higher than the line your tile was set to. The result can be a gap too wide for caulk. If the backsplash is due for a change anyway, plan both jobs together; if not, ask your installer how breakage is handled before the old top comes out. When to install a backsplash in a remodel, step by step Deciding when to install a backsplash comes down to what has to be finished around it. Sort out three things before the first tile goes up. Should you paint before installing the backsplash? Yes. Long-standing remodeling advice is to prime and paint the walls before cabinets and backsplash go in, then touch up at the end. That band of wall under the uppers is awkward to reach once finished surfaces box it in, and painting it early means your brush never cuts a line against new tile. For peel-and-stick materials there is a second reason to paint early, covered below: fresh paint needs time before anything adhesive goes over it. Plan the bottom row before the counters arrive You cannot set the backsplash before the counter, but you can design it. Decide where the field starts and stops, how it meets the window and the cabinet returns, and how it lands at the range. Settle the finish while the counter is still a sample on the table; matching a metal finish to your counter and cabinets walks through that choice. Range and outlets come after Practical sequencing puts the range in after the backsplash, or pulls it out while the wall is worked. Outlets and switches are trimmed out last, because any backsplash adds depth to the wall. Electrical code lets a box sit no more than 1/4 inch back from a noncombustible finish, so when a new backsplash pushes the wall out further, an electrician adds a listed box extender to bring it forward. Our article on thin backsplash tile explains where that depth shows up. How long does it take to do a backsplash? For a conventional tile backsplash, the labor is shorter than the calendar, because most of the time goes to waiting. Setting the tile. A standard thinset mortar is typically left about 24 hours before grouting, according to setting-material data sheets. Rapid-setting mortars cut that to a couple of hours. Grouting. Once the grout is in, cementitious grout generally needs to cure before it is sealed. Manufacturers diverge, and many quote roughly 48 to 72 hours, while some newer grouts need no sealer at all. Follow the label on the product you buy. The counter joint. Where tile meets the countertop, the tile industry calls for a flexible sealant, not grout, because that seam is a change of plane where two materials move differently. The sealant goes on after the grout has set. Put together, a small kitchen backsplash in tile can easily stretch across two or three days of on-and-off work for a careful DIYer, and longer if you seal the grout or hit a slow-curing product. The difficulty sits in the cutting: outlets, window returns and the end of a run take most of the skill. Stone counters add their own wait before any of this starts. The gap between templating and installation is often one to three weeks, and longer when a shop has a queue, so ask your fabricator for their current lead time and keep the backsplash materials in the garage until the top is down. Where peel-and-stick metal tile fits the schedule An adhesive-backed aluminum tile changes the length of the backsplash step, not its place in the sequence. It still goes on after the counter, because the counter is still the edge you build from. What disappears is the waiting. With no mortar to set and no grout to cure, the tiling itself can fit into a single afternoon. The product page lists the whole routine: measure, clean and dry the wall, plan the layout, then peel and press every tile down firmly. Cutting a tile to size calls for a box cutter or scissors, nothing more specialized. That speed makes the order around it more important, not less. The paint has to be ready. WallWear asks for a clean, dry, smooth surface and notes the tiles are not suited to textured walls. Paint can be dry to the touch within an hour and still be weeks from fully cured, and several makers of peel-and-stick wall products ask for roughly three to four weeks after painting. WallWear does not publish a wait of its own, so if you have just painted, check with our team before you stick down the first row. The counter has to be in and clean. Clear fabrication dust and stray silicone before you press the bottom row. The range zone has a clearance. WallWear recommends keeping the tile at least 10 inches from the stovetop, so measure and mark that line from the cooktop before the range comes out. It can also help after a counter swap, with a condition attached. If the old tile survives intact and you simply want a new look, metal tile can go over it when that surface is clean and flat, its grout joints filled level and its face smooth. Chipped tile or an open gap at the counter needs repairing first. What that surface needs is laid out in going over old tile with metal, and the full method, from bare wall to last row, lives in the peel and stick metal tile walkthrough. A cool Silver Fleur pattern reads crisp next to white quartz, the warm tone of Patina Copper settles in beside butcher block or warm granite, and Teal and Silver Leaves gives a pale counter some color to play against. Each pack of ten 8 x 8 inch tiles covers approximately 4.44 square feet, so measure the run once the counter is in and order from those real numbers. Frequently Asked Questions Do you install the backsplash before the countertop? No. In almost every kitchen the countertop goes in first and the backsplash follows. The counter's finished height is only known once it is installed on leveled cabinets, and the backsplash starts from that edge. Tiling first means guessing the bottom line and risking damage when a heavy slab is set. Many fabricators also measure a full-height stone splash after the counters are down. Should you paint before installing a backsplash? Yes. Prime and paint the walls before the backsplash goes in, then touch up afterward. The narrow strip between counter and upper cabinets is hard to reach later, and you avoid cutting paint against new tile. For a peel-and-stick backsplash, paint even earlier, because fresh paint needs time to cure before adhesive goes over it, often several weeks. How long should you wait to grout a backsplash? With a standard thinset mortar, the usual wait is about 24 hours before grouting, per manufacturer data sheets. Rapid-setting mortars can be ready in a couple of hours, so read the bag. After grouting, many cement grouts need roughly 48 to 72 hours before sealing. Peel-and-stick metal tile skips both waits, since it has no mortar and no grout. Can you replace countertops without replacing the backsplash? Sometimes, but plan for trouble at the bottom row. Tile set tight against the old counter can chip or pull drywall when the top is removed, so cut the caulk line first. A new counter of a different thickness may also leave a gap or overlap. For many kitchens it is the natural moment to redo or cover the backsplash. Does a backsplash add value to a home? No reliable data puts a resale number on a backsplash by itself. Appraisers and cost-versus-value studies look at kitchen projects as a whole, and minor kitchen updates tend to recover a good share of their cost. A finished backsplash mostly adds appeal: a kitchen with bare drywall behind the counter reads as unfinished to buyers walking through it.